V 型槽开口角度对端面干气密封稳态
特性的数值分析

doi:10.16638/j.cnki.1671-7988.2023.012.012

汽车实用技术 ›› 2023, Vol. 48 ›› Issue (12): 60-66.DOI: 10.16638/j.cnki.1671-7988.2023.012.012

• 设计研究 • 上一篇

V 型槽开口角度对端面干气密封稳态特性的数值分析

杨玺庆，王宇飞，马高峰

兰州石化职业技术大学机械工程学院

出版日期:2023-06-30 发布日期:2023-06-30
通讯作者: 杨玺庆
作者简介:杨玺庆（1988－），硕士，讲师，研究方向为机械密封，E-mail:895191744＠qq.com。
基金资助:
2021 年度甘肃省自然科学基金（21JR7RA775）。

Numerical Analysis of the Steady-state Characteristics of V-groove Opening Angle on End Face Dry Gas Seals

YANG Xiqing, WANG Yufei, MA Gaofeng

College of Mechanical Engineering, Lanzhou Petrochemical University of Vocational Technology,

Online:2023-06-30 Published:2023-06-30
Contact: YANG Xiqing

摘要/Abstract

摘要： 端面干气密封已广泛应用于化工旋转机械中，但对于其密封副的双向旋转槽型缺少系统的研究。针对 V 型槽端面干气密封运行原理和结构特点，在气膜润滑理论的基础上，建立了相应的数学模型。采用中心差分法对压力和气膜厚度控制方程进行了耦合求解，并验证了编制程序的正确性。随后利用验证后的代码对端面干气密封的稳态特性参数展开了计算，并分析讨论了工况参数改变时 V 型槽不同的开口角度对端面干气密封稳态特性参数的影响。研究表明：本研究所数学模型具有一定的普适性，而且 V 型槽开口角度为 α=15°的密封性能最好，四种开口角度所产生的密封效果优劣排序为 α=15°>α=60°>α=30°>α=45°。V 型槽端面干气密封在所讨论的工况参数范围内，气膜开启力和气膜摩擦力随转速和压力的增大而提高；泄漏量随转速的增大略微下降，随压力的增大而呈线性增大。此研究结果为端面干气密封的双向旋转槽型的设计与研究提供了参考依据。

关键词: 端面干气密封；有限差分法；V 型槽型；干气密封；稳态特性

Abstract: End face dry gas seals have been widely used in chemical rotating machinery, but there is a lack of systematic research on the bi-directional rotating groove type of its sealing sub. The corresponding mathematical model is established based on the theory of gas film lubrication for the operating principle and structural characteristics of V-groove face dry gas seal. The coupled solution of the pressure and gas film thickness control equations was carried out using the central difference method, and the correctness of the prepared program was verified. Then, the steady-state charac-teristics of the end face dry gas seal are calculated using the validated code, and the effect of different opening angles of the V-groove on the steady-state characteristics of the end face dry gas seal when the operating parameters are changed is analyzed and discussed. The study shows that the mathematical model is universal and the best sealing performance is achieved with the opening angle of V-groove α=15°, and the sealing effect of the four opening angles is ranked as follows α=15°> α=60°>α=30°>α=45°. The leakage volume decreases slightly with the increase of rotational speed and increases linearly with the increase of pressure. The results of this study provide a reference for the design and research of bi-directional rotating groove type of end face dry gas seal.

Key words: End-face gas film seal; Finite difference method; V-groove type; Dry gas seal; Steadystate characteristic

杨玺庆. V 型槽开口角度对端面干气密封稳态特性的数值分析[J]. 汽车实用技术, 2023, 48(12): 60-66.

YANG Xiqing. Numerical Analysis of the Steady-state Characteristics of V-groove Opening Angle on End Face Dry Gas Seals[J]. Automobile Applied Technology, 2023, 48(12): 60-66.

参考文献

[ 1 ] XU W,YANG J.Explicit Solution of Gas Film Pressure for Performance Calculation of Spiral Grooved Gas Seals[J].Journal of Mechanical Science and Technology,2018,32:277-282. [ 2 ] DU Q,GAO K, ZHANG D,et al.Effects of Grooved Ring Rotation and Working Fluid on the Performance of Dry Gas Seal[J].International Journal of Heat and Mass Transfer,2018,126:1323-1332. [ 3 ] BLASIAK S.Numerical Modeling and Analysis of the Noncontacting Impulse Gas Face Seals[J].Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology,2019,233(8):1139- 1153. [ 4 ] CHáVEZ A,DE SANTIAGO O.Experimental Measurements of the Thermo Elastic Behavior of a Dry Gas Seal Operating with Logarithmic Spiral Grooves of 11° and 15°[J].Proceedings of the Institution of Mechanical Engineers,Part J:Journal of Engineering Tribology,2021,235(9):1807-1819. [ 5 ] SHAHIN I.Gas Seal Performance and Start Up Condition Enhancing with Different Seal Groove Geometries[J].Journal of Aeronautics & Aerospace Engineering,2016,5(4):1000177. [ 6 ] 于辰,江锦波,赵文静,等.基于微段组合的干气密封端面型槽结构模型及其参数影响[J].化工学报,2021, 72(10):5294-5309. [ 7 ] 陈志,范唯超,陶杰,等.双向旋转梯形槽干气密封流场的数值模拟[J].四川大学学报(工程科学版),2015,47(1):180-185. [ 8 ] ZHANG H, HUANG W, WANG Y, et al. Research on Meshfree Method for Analyzing Seal Behavior of a T-DGS[J]. International Journal of Precision Engineering and Manufacturing,2017,18:529-536. [ 9 ] SU H,RAHMANI R,RAHNEJAT H.Performance Evaluation of Bidirectional Dry Gas Seals with Special Groove Geometry[J].Tribology Transactions,2017,60 (1):58-69. [10] WEIBING Z,HESHUN W,SHENGREN Z,et al.Research on Face Fluid Field and Seal Performance of T-shape Groove Dry Gas Seal[C]//2009 Second International Conference on Intelligent Computation Technology and Automation.Piscataway:IEEE,2009,2:902- 906. [11] 王衍,孙见君,胡琼,等.基于微尺度造型的干气密封流动有序性数值分析[J].摩擦学学报,2018,38(6):673- 683. [12] 王衍,王达,胡琼,等.基于 CFD 的 T 形槽气膜密封网格无关性分析 [J].润滑与密封 ,2018,43(11):70-73, 113. [13] 王衍,胡琼,朱强,等.T 形槽气膜密封槽底粗糙度有序造型的扰流效应[J].润滑与密封, 2019,44(4): 55-62. [14] 莫陇刚,丁雪兴,严如奇,等.仿树形槽干气密封稳态性能分析[J].润滑与密封, 2022,47(12): 68-74. [15] 孙鑫晖,闫方琦,李振涛,等.枞树型槽上游泵送机械密封稳态特性数值分析[J].润滑与密封,2018,43(12): 76-80. [16] 马媛媛,彭旭东,白少先,等.双向旋转树型槽密封端面气膜动压特性[J].流体机械, 2012,40(1):13-16,5. [17] 徐奇超,江锦波,彭旭东,等.基于遗传算法的干气密封双向槽统一模型与参数优化[J].化工学报,2019,70 (3):995-1005,782. [18] 刘正先,田广胜,刘艳梅.螺旋槽干气密封运行特性的预测模型及试验研究[J].天津大学学报(自然科学与工程技术版),2018,51(5):466-474. [19] 张轩,宋鹏云.T 槽干气密封低速运转特性的理论研究[J].润滑与密封, 2010,35(10):49-54. [20] 彭旭东,张岳林,白少先,等.转速压力对 T 型槽干气密封槽型几何结构参数优选值的影响[J].化工学报, 2012,63(2):551-559. [21] 胡琼,王衍,戴嵘,等.基于有序微造型的圆弧线槽干气密封性能分析[J].化工学报,2019,70(3):1006-1015. [22] 严如奇,丁雪兴,徐洁,等.离心惯性力效应对超临界二氧化碳干气密封流场与密封特性影响分析[J].摩擦学学报,2020,40(6):781-791.

V 型槽开口角度对端面干气密封稳态特性的数值分析

Numerical Analysis of the Steady-state Characteristics of V-groove Opening Angle on End Face Dry Gas Seals

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

V 型槽开口角度对端面干气密封稳态 特性的数值分析

Numerical Analysis of the Steady-state Characteristics of V-groove Opening Angle on End Face Dry Gas Seals

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

V 型槽开口角度对端面干气密封稳态特性的数值分析